Based on kernel version 6.11
. Page generated on 2024-09-24 08:21 EST
.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 | # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- $id: http://devicetree.org/schemas/sound/cirrus,cs42l42.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Cirrus Logic CS42L42 audio CODEC maintainers: - patches@opensource.cirrus.com description: The CS42L42 is a low-power audio codec designed for portable applications. It provides a high-dynamic range, stereo DAC for audio playback and a mono high-dynamic-range ADC for audio capture. There is an integrated headset detection block. properties: compatible: enum: - cirrus,cs42l42 - cirrus,cs42l83 reg: description: The I2C address of the CS42L42. maxItems: 1 VP-supply: description: VP power supply. VCP-supply: description: Charge pump power supply. VD_FILT-supply: description: FILT+ power supply. VL-supply: description: Logic power supply. VA-supply: description: Analog power supply. reset-gpios: description: This pin will be asserted and then deasserted to reset the CS42L42 before communication starts. maxItems: 1 interrupts: description: Interrupt for CS42L42 IRQ line. maxItems: 1 cirrus,ts-inv: description: | Sets the behaviour of the jack plug detect switch. 0 - (Default) Shorted to tip when unplugged, open when plugged. This is "inverted tip sense (ITS)" in the datasheet. 1 - Open when unplugged, shorted to tip when plugged. This is "normal tip sense (TS)" in the datasheet. The CS42L42_TS_INV_* defines are available for this. $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 1 cirrus,ts-dbnc-rise: description: | Debounce the rising edge of TIP_SENSE_PLUG. With no debounce, the tip sense pin might be noisy on a plug event. 0 - 0ms 1 - 125ms 2 - 250ms 3 - 500ms 4 - 750ms 5 - 1s (Default) 6 - 1.25s 7 - 1.5s The CS42L42_TS_DBNCE_* defines are available for this. $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 7 cirrus,ts-dbnc-fall: description: | Debounce the falling edge of TIP_SENSE_UNPLUG. With no debounce, the tip sense pin might be noisy on an unplug event. 0 - 0ms 1 - 125ms 2 - 250ms 3 - 500ms 4 - 750ms 5 - 1s (Default) 6 - 1.25s 7 - 1.5s The CS42L42_TS_DBNCE_* defines are available for this. $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 7 cirrus,btn-det-init-dbnce: description: | This sets how long to wait after enabling button detection interrupts before servicing button interrupts, to allow the HS bias time to settle. Value is in milliseconds. There may be erroneous button interrupts if this debounce time is too short. 0ms - 200ms, Default = 100ms $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 200 cirrus,btn-det-event-dbnce: description: | This sets how long to wait after receiving a button press interrupt before processing it. Allows time for the button press to make a clean connection with the bias resistors. Value is in milliseconds. 0ms - 20ms, Default = 10ms $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 20 cirrus,bias-lvls: description: | For a level-detect headset button scheme, each button will bias the mic pin to a certain voltage. To determine which button was pressed, the voltage is compared to sequential, decreasing voltages, until the compared voltage < bias voltage. For different hardware setups, a designer might want to tweak this. This is an array of descending values for the comparator voltage, given as percent of the HSBIAS voltage. Array of 4 values, each 0-63 < x1 x2 x3 x4 > Default = < 15 8 4 1 > $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 4 maxItems: 4 items: minimum: 0 maximum: 63 cirrus,hs-bias-ramp-rate: description: | If present this sets the rate that the HS bias should rise and fall. The actual rise and fall times depend on external hardware (the datasheet gives several rise and fall time examples). 0 - Fast rise time; slow, load-dependent fall time 1 - Fast 2 - Slow (default) 3 - Slowest The CS42L42_HSBIAS_RAMP_* defines are available for this. $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 3 cirrus,hs-bias-sense-disable: description: | If present the HSBIAS sense is disabled. Configures HSBIAS output current sense through the external 2.21-k resistor. HSBIAS_SENSE is a hardware feature to reduce the potential pop noise when the headset plug is removed slowly. But on some platforms ESD voltage will affect it causing plug detection to fail, especially with CTIA headset type. For different hardware setups, a designer might want to tweak default behavior. type: boolean required: - compatible - reg - VP-supply - VCP-supply - VD_FILT-supply - VL-supply - VA-supply additionalProperties: false examples: - | #include <dt-bindings/sound/cs42l42.h> i2c { #address-cells = <1>; #size-cells = <0>; cs42l42: cs42l42@48 { compatible = "cirrus,cs42l42"; reg = <0x48>; VA-supply = <&dummy_vreg>; VP-supply = <&dummy_vreg>; VCP-supply = <&dummy_vreg>; VD_FILT-supply = <&dummy_vreg>; VL-supply = <&dummy_vreg>; reset-gpios = <&axi_gpio_0 1 0>; interrupt-parent = <&gpio0>; interrupts = <55 8>; cirrus,ts-inv = <CS42L42_TS_INV_DIS>; cirrus,ts-dbnc-rise = <CS42L42_TS_DBNCE_1000>; cirrus,ts-dbnc-fall = <CS42L42_TS_DBNCE_0>; cirrus,btn-det-init-dbnce = <100>; cirrus,btn-det-event-dbnce = <10>; cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>; cirrus,hs-bias-ramp-rate = <CS42L42_HSBIAS_RAMP_SLOW>; }; }; |