# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
# Copyright 2025 Realtek Semiconductor Corporation
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/realtek,rtd1625-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Realtek DHC RTD1625 Pin Controller

maintainers:
  - Tzuyi Chang <tychang@realtek.com>
  - Yu-Chun Lin <eleanor.lin@realtek.com>

description:
  The Realtek DHC RTD1625 is a high-definition media processor SoC. The
  RTD1625 pin controller is used to control pin function, pull-up/down
  resistors, drive strength, slew rate, Schmitt trigger, power source
  (I/O output voltage), input threshold domain selection and a higher-VIL mode.

properties:
  compatible:
    items:
      - enum:
          - realtek,rtd1625-iso-pinctrl
          - realtek,rtd1625-main2-pinctrl
          - realtek,rtd1625-isom-pinctrl
          - realtek,rtd1625-ve4-pinctrl

  reg:
    maxItems: 1

patternProperties:
  '-pins$':
    type: object
    allOf:
      - $ref: pincfg-node.yaml#
      - $ref: pinmux-node.yaml#

    properties:
      pins:
        items:
          enum: [gpio_0, gpio_1, gpio_2, gpio_3, gpio_4, gpio_5, gpio_6,
                 gpio_7, gpio_8, gpio_9, gpio_10, gpio_11, gpio_12, gpio_13,
                 gpio_14, gpio_15, gpio_16, gpio_17, gpio_18, gpio_19, gpio_20,
                 gpio_21, gpio_22, gpio_23, gpio_24, gpio_25, gpio_28, gpio_29,
                 gpio_30, gpio_31, gpio_32, gpio_33, gpio_34, gpio_35, gpio_40,
                 gpio_41, gpio_42, gpio_43, gpio_44, gpio_45, gpio_46, gpio_47,
                 gpio_48, gpio_49, gpio_50, gpio_51, gpio_52, gpio_53, gpio_54,
                 gpio_55, gpio_56, gpio_57, gpio_58, gpio_59, gpio_60, gpio_61,
                 gpio_62, gpio_63, gpio_64, gpio_65, gpio_66, gpio_67, gpio_80,
                 gpio_81, gpio_82, gpio_83, gpio_84, gpio_85, gpio_86, gpio_87,
                 gpio_88, gpio_89, gpio_90, gpio_91, gpio_92, gpio_93, gpio_94,
                 gpio_95, gpio_96, gpio_97, gpio_98, gpio_99, gpio_100,
                 gpio_101, gpio_102, gpio_103, gpio_104, gpio_105, gpio_106,
                 gpio_107, gpio_108, gpio_109, gpio_110, gpio_111, gpio_112,
                 gpio_128, gpio_129, gpio_130, gpio_131, gpio_132, gpio_133,
                 gpio_134, gpio_135, gpio_136, gpio_137, gpio_138, gpio_139,
                 gpio_140, gpio_141, gpio_142, gpio_143, gpio_144, gpio_145,
                 gpio_146, gpio_147, gpio_148, gpio_149, gpio_150, gpio_151,
                 gpio_152, gpio_153, gpio_154, gpio_155, gpio_156, gpio_157,
                 gpio_158, gpio_159, gpio_160, gpio_161, gpio_162, gpio_163,
                 gpio_164, gpio_165, ai_i2s1_loc, ao_i2s1_loc, arm_trace_dbg_en,
                 csi_vdsel, ejtag_acpu_loc, ejtag_aucpu0_loc, ejtag_aucpu1_loc,
                 ejtag_pcpu_loc, ejtag_scpu_loc, ejtag_ve2_loc, emmc_clk,
                 emmc_cmd, emmc_data_0, emmc_data_1, emmc_data_2, emmc_data_3,
                 emmc_data_4, emmc_data_5, emmc_data_6, emmc_data_7,
                 emmc_dd_sb, emmc_rst_n, etn_phy_loc, hif_clk, hif_data,
                 hif_en, hif_rdy, hi_width, i2c6_loc, ir_rx_loc, rgmii_vdsel,
                 sf_en, spdif_in_mode, spdif_loc, uart0_loc, usb_cc1, usb_cc2,
                 ve4_uart_loc]

      function:
        enum: [gpio, ai_i2s0, ai_i2s2, ai_tdm0, ai_tdm1, ai_tdm2, ao_i2s0,
               ao_i2s2, ao_tdm0, ao_tdm1, ao_tdm2, csi0, csi1, csi_1v2, csi_1v8,
               csi_2v5, csi_3v3, dmic0, dmic1, dmic2, dptx_hpd, edptx_hdp, emmc,
               gspi0, gspi1, gspi2, hi_width_1bit, hi_width_disable, i2c0, i2c1,
               i2c3, i2c4, i2c5, i2c7, iso_tristate, pcie0, pcie1, pcm, pctrl,
               pwm4, pwm5, pwm6, rgmii, rgmii_1v2, rgmii_1v8, rgmii_2v5,
               rgmii_3v3, rmii, sd, sdio, sf_disable, sf_enable,
               spdif_in_coaxial, spdif_in_gpio, spdif_out, spi, ts0, ts1, uart1,
               uart2, uart3, uart4, uart5, uart6, uart7, uart8, uart9, uart10,
               usb_cc1, usb_cc2, vi0_dtv, vi1_dtv, vtc_ao_i2s, vtc_dmic,
               vtc_i2s, ai_i2s1_loc0, ai_i2s1_loc1, ao_i2s0_loc0, ao_i2s0_loc1,
               ao_i2s1_loc0, ao_i2s1_loc1, ao_tdm1_loc0, ao_tdm1_loc1,
               etn_led_loc0, etn_led_loc1, etn_phy_loc0, etn_phy_loc1,
               i2c6_loc0, i2c6_loc1, ir_rx_loc0, ir_rx_loc1, pwm0_loc0,
               pwm0_loc1, pwm0_loc2, pwm0_loc3, pwm1_loc0, pwm1_loc1, pwm2_loc0,
               pwm2_loc1, pwm3_loc0, pwm3_loc1, spdif_loc0, spdif_loc1,
               uart0_loc0, uart0_loc1, ve4_uart_loc0, ve4_uart_loc1,
               ve4_uart_loc2, acpu_ejtag_loc0, acpu_ejtag_loc1, acpu_ejtag_loc2,
               aucpu0_ejtag_loc0, aucpu0_ejtag_loc1, aucpu0_ejtag_loc2,
               aucpu1_ejtag_loc0, aucpu1_ejtag_loc1, aucpu1_ejtag_loc2,
               aupu0_ejtag_loc1, aupu1_ejtag_loc1, gpu_ejtag_loc0,
               pcpu_ejtag_loc0, pcpu_ejtag_loc1, pcpu_ejtag_loc2,
               scpu_ejtag_loc0, scpu_ejtag_loc1, scpu_ejtag_loc2,
               ve2_ejtag_loc0, ve2_ejtag_loc1, ve2_ejtag_loc2, pll_test_loc0,
               pll_test_loc1, dbg_out1, isom_dbg_out, arm_trace_debug_disable,
               arm_trace_debug_enable]

      drive-strength:
        enum: [4, 8]

      bias-pull-down: true

      bias-pull-up: true

      bias-disable: true

      input-schmitt-enable: true

      input-schmitt-disable: true

      input-threshold-voltage-microvolt:
        description: |
          Select the input receiver voltage domain for the pin.
          Valid arguments are:
          - 1800000: 1.8V input logic level
          - 3300000: 3.3V input logic level
        enum: [1800000, 3300000]

      drive-push-pull: true

      power-source:
        description: |
          Valid arguments are described as below:
          0: power supply of 1.8V
          1: power supply of 3.3V
        enum: [0, 1]

      slew-rate:
        description: |
          Valid arguments are described as below:
            1: ~1ns falling time
            10: ~10ns falling time
            20: ~20ns falling time
            30: ~30ns falling time
        enum: [1, 10, 20, 30]

      realtek,drive-strength-p:
        description: |
          Some of pins can be driven using the P-MOS and N-MOS transistor to
          achieve finer adjustments. The block-diagram representation is as
          follows:
                         VDD
                          |
                      ||--+
               +-----o||     P-MOS-FET
               |      ||--+
          IN --+          +----- out
               |      ||--+
               +------||     N-MOS-FET
                      ||--+
                          |
                         GND
          The driving strength of the P-MOS/N-MOS transistors impacts the
          waveform's rise/fall times. Greater driving strength results in
          shorter rise/fall times. Each P-MOS and N-MOS transistor offers
          8 configurable levels (0 to 7), with higher values indicating
          greater driving strength, contributing to achieving the desired
          speed.
 
          The realtek,drive-strength-p is used to control the driving strength
          of the P-MOS output.
 
          This value is not a simple count of transistors. Instead, it
          represents a weighted configuration. There is a base driving
          capability (even at value 0), and each bit adds a different weight to
          the total strength. The resulting current is non-linear and varies
          significantly based on the IO voltage (1.8V vs 3.3V) and the specific
          pad group.
        $ref: /schemas/types.yaml#/definitions/uint32
        minimum: 0
        maximum: 7

      realtek,drive-strength-n:
        description: |
          Similar to the realtek,drive-strength-p, the realtek,drive-strength-n
          is used to control the driving strength of the N-MOS output.
 
          This property uses the same weighted configuration logic where values
          0-7 represent non-linear strength adjustments rather than a transistor
          count.
 
          Higher values indicate greater driving strength, resulting in shorter
          fall times.
        $ref: /schemas/types.yaml#/definitions/uint32
        minimum: 0
        maximum: 7

      realtek,duty-cycle:
        description: |
          An integer describing the level to adjust the output pulse width, it
          provides a fixed nanosecond-level adjustment to the rising/falling
          edges of an existing signal. It is used for Signal Integrity tuning
          (adding/subtracting delay to fine-tune the high/low duration), rather
          than generating a specific PWM frequency.
 
          Valid arguments are described as below:
          0: 0ns
          2: + 0.25ns
          3: + 0.5ns
          4: -0.25ns
          5: -0.5ns
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [0, 2, 3, 4, 5]

      realtek,high-vil-microvolt:
        description: |
          The threshold value for the input receiver's LOW recognition (VIL).
 
          This property is used to address specific HDMI I2C compatibility
          issues where some sinks (TVs) have weak pull-down capabilities and
          fail to pull the bus voltage below the standard VIL threshold
          (~0.7V).
 
          Setting this property to 1100000 (1.1V) enables a specialized input
          receiver mode that raises the effective VIL threshold to improve
          detection.
        enum: [1100000]

    required:
      - pins

    additionalProperties: false

required:
  - compatible
  - reg

additionalProperties: false

examples:
  - |
    pinctrl@4e000 {
        compatible = "realtek,rtd1625-iso-pinctrl";
        reg = <0x4e000 0x130>;
 
        emmc-hs200-pins {
            pins = "emmc_clk",
                   "emmc_cmd",
                   "emmc_data_0",
                   "emmc_data_1",
                   "emmc_data_2",
                   "emmc_data_3",
                   "emmc_data_4",
                   "emmc_data_5",
                   "emmc_data_6",
                   "emmc_data_7";
            function = "emmc";
            realtek,drive-strength-p = <2>;
            realtek,drive-strength-n = <2>;
        };
 
        i2c-0-pins {
            pins = "gpio_12",
                   "gpio_13";
            function = "i2c0";
            drive-strength = <4>;
        };
    };