Based on kernel version 6.10
. Page generated on 2024-07-16 09:00 EST
.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 | # SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) # Copyright (C) 2019 Texas Instruments Incorporated %YAML 1.2 --- $id: http://devicetree.org/schemas/sound/tlv320adcx140.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Texas Instruments TLV320ADCX140 Quad Channel Analog-to-Digital Converter maintainers: - Andrew Davis <afd@ti.com> description: | The TLV320ADCX140 are multichannel (4-ch analog recording or 8-ch digital PDM microphones recording), high-performance audio, analog-to-digital converter (ADC) with analog inputs supporting up to 2V RMS. The TLV320ADCX140 family supports line and microphone Inputs, and offers a programmable microphone bias or supply voltage generation. Specifications can be found at: https://www.ti.com/lit/ds/symlink/tlv320adc3140.pdf https://www.ti.com/lit/ds/symlink/tlv320adc5140.pdf https://www.ti.com/lit/ds/symlink/tlv320adc6140.pdf properties: compatible: enum: - ti,tlv320adc3140 - ti,tlv320adc5140 - ti,tlv320adc6140 reg: maxItems: 1 description: | I2C address of the device can be one of these 0x4c, 0x4d, 0x4e or 0x4f reset-gpios: maxItems: 1 description: | GPIO used for hardware reset. areg-supply: description: | Regulator with AVDD at 3.3V. If not defined then the internal regulator is enabled. ti,mic-bias-source: description: | Indicates the source for MIC Bias. 0 - Mic bias is set to VREF 1 - Mic bias is set to VREF × 1.096 6 - Mic bias is set to AVDD $ref: /schemas/types.yaml#/definitions/uint32 enum: [0, 1, 6] ti,vref-source: description: | Indicates the source for MIC Bias. 0 - Set VREF to 2.75V 1 - Set VREF to 2.5V 2 - Set VREF to 1.375V $ref: /schemas/types.yaml#/definitions/uint32 enum: [0, 1, 2] ti,pdm-edge-select: description: | Defines the PDMCLK sampling edge configuration for the PDM inputs. This array is defined as <PDMIN1 PDMIN2 PDMIN3 PDMIN4>. 0 - (default) Odd channel is latched on the negative edge and even channel is latched on the positive edge. 1 - Odd channel is latched on the positive edge and even channel is latched on the negative edge. PDMIN1 - PDMCLK latching edge used for channel 1 and 2 data PDMIN2 - PDMCLK latching edge used for channel 3 and 4 data PDMIN3 - PDMCLK latching edge used for channel 5 and 6 data PDMIN4 - PDMCLK latching edge used for channel 7 and 8 data $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 1 maxItems: 4 items: maximum: 1 default: [0, 0, 0, 0] ti,gpi-config: description: | Defines the configuration for the general purpose input pins (GPI). The array is defined as <GPI1 GPI2 GPI3 GPI4>. 0 - (default) disabled 1 - GPIX is configured as a general-purpose input (GPI) 2 - GPIX is configured as a master clock input (MCLK) 3 - GPIX is configured as an ASI input for daisy-chain (SDIN) 4 - GPIX is configured as a PDM data input for channel 1 and channel (PDMDIN1) 5 - GPIX is configured as a PDM data input for channel 3 and channel (PDMDIN2) 6 - GPIX is configured as a PDM data input for channel 5 and channel (PDMDIN3) 7 - GPIX is configured as a PDM data input for channel 7 and channel (PDMDIN4) $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 1 maxItems: 4 items: maximum: 7 default: [0, 0, 0, 0] ti,gpio-config: description: | Defines the configuration and output drive for the General Purpose Input and Output pin (GPIO1). Its value is a pair, the first value is for the configuration type and the second value is for the output drive type. The array is defined as <GPIO1_CFG GPIO1_DRV> configuration for the GPIO pin can be one of the following: 0 - disabled 1 - GPIO1 is configured as a general-purpose output (GPO) 2 - (default) GPIO1 is configured as a device interrupt output (IRQ) 3 - GPIO1 is configured as a secondary ASI output (SDOUT2) 4 - GPIO1 is configured as a PDM clock output (PDMCLK) 8 - GPIO1 is configured as an input to control when MICBIAS turns on or off (MICBIAS_EN) 9 - GPIO1 is configured as a general-purpose input (GPI) 10 - GPIO1 is configured as a master clock input (MCLK) 11 - GPIO1 is configured as an ASI input for daisy-chain (SDIN) 12 - GPIO1 is configured as a PDM data input for channel 1 and channel 2 (PDMDIN1) 13 - GPIO1 is configured as a PDM data input for channel 3 and channel 4 (PDMDIN2) 14 - GPIO1 is configured as a PDM data input for channel 5 and channel 6 (PDMDIN3) 15 - GPIO1 is configured as a PDM data input for channel 7 and channel 8 (PDMDIN4) output drive type for the GPIO pin can be one of the following: 0 - Hi-Z output 1 - Drive active low and active high 2 - (default) Drive active low and weak high 3 - Drive active low and Hi-Z 4 - Drive weak low and active high 5 - Drive Hi-Z and active high $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 2 maxItems: 2 items: maximum: 15 default: [2, 2] ti,asi-tx-drive: type: boolean description: | When set the device will set the Tx ASI output to a Hi-Z state for unused data cycles. Default is to drive the output low on unused ASI cycles. patternProperties: '^ti,gpo-config-[1-4]$': $ref: /schemas/types.yaml#/definitions/uint32-array description: | Defines the configuration and output driver for the general purpose output pins (GPO). These values are pairs, the first value is for the configuration type and the second value is for the output drive type. The array is defined as <GPO_CFG GPO_DRV> GPO output configuration can be one of the following: 0 - (default) disabled 1 - GPOX is configured as a general-purpose output (GPO) 2 - GPOX is configured as a device interrupt output (IRQ) 3 - GPOX is configured as a secondary ASI output (SDOUT2) 4 - GPOX is configured as a PDM clock output (PDMCLK) GPO output drive configuration for the GPO pins can be one of the following: 0d - (default) Hi-Z output 1d - Drive active low and active high 2d - Drive active low and weak high 3d - Drive active low and Hi-Z 4d - Drive weak low and active high 5d - Drive Hi-Z and active high required: - compatible - reg additionalProperties: false examples: - | #include <dt-bindings/gpio/gpio.h> i2c { #address-cells = <1>; #size-cells = <0>; codec: codec@4c { compatible = "ti,tlv320adc5140"; reg = <0x4c>; ti,mic-bias-source = <6>; ti,pdm-edge-select = <0 1 0 1>; ti,gpi-config = <4 5 6 7>; ti,gpio-config = <10 2>; ti,gpo-config-1 = <0 0>; ti,gpo-config-2 = <0 0>; reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; }; }; |