Documentation / devicetree / bindings / sound / rt5645.txt


Based on kernel version 6.10. Page generated on 2024-07-16 09:00 EST.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82
RT5650/RT5645 audio CODEC

This device supports I2C only.

Required properties:

- compatible : One of "realtek,rt5645" or "realtek,rt5650".

- reg : The I2C address of the device.

- interrupts : The CODEC's interrupt output.

- avdd-supply: Power supply for AVDD, providing 1.8V.

- cpvdd-supply: Power supply for CPVDD, providing 3.5V.

Optional properties:

- hp-detect-gpios:
  a GPIO spec for the external headphone detect pin. If jd-mode = 0,
  we will get the JD status by getting the value of hp-detect-gpios.

- cbj-sleeve-gpios:
  a GPIO spec to control the external combo jack circuit to tie the sleeve/ring2
  contacts to the ground or floating. It could avoid some electric noise from the
  active speaker jacks.

- realtek,in2-differential
  Boolean. Indicate MIC2 input are differential, rather than single-ended.

- realtek,dmic1-data-pin
  0: dmic1 is not used
  1: using IN2P pin as dmic1 data pin
  2: using GPIO6 pin as dmic1 data pin
  3: using GPIO10 pin as dmic1 data pin
  4: using GPIO12 pin as dmic1 data pin

- realtek,dmic2-data-pin
  0: dmic2 is not used
  1: using IN2N pin as dmic2 data pin
  2: using GPIO5 pin as dmic2 data pin
  3: using GPIO11 pin as dmic2 data pin

-- realtek,jd-mode : The JD mode of rt5645/rt5650
   0 : rt5645/rt5650 JD function is not used
   1 : Mode-0 (VDD=3.3V), two port jack detection
   2 : Mode-1 (VDD=3.3V), one port jack detection
   3 : Mode-2 (VDD=1.8V), one port jack detection

Pins on the device (for linking into audio routes) for RT5645/RT5650:

  * DMIC L1
  * DMIC R1
  * DMIC L2
  * DMIC R2
  * IN1P
  * IN1N
  * IN2P
  * IN2N
  * Haptic Generator
  * HPOL
  * HPOR
  * LOUTL
  * LOUTR
  * PDM1L
  * PDM1R
  * SPOL
  * SPOR

Example:

codec: rt5650@1a {
	compatible = "realtek,rt5650";
	reg = <0x1a>;
	hp-detect-gpios = <&gpio 19 0>;
	cbj-sleeve-gpios = <&gpio 20 0>;
	interrupt-parent = <&gpio>;
	interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
	realtek,dmic-en = "true";
	realtek,en-jd-func = "true";
	realtek,jd-mode = <3>;
};