Documentation / hwmon / w83627ehf.rst


Based on kernel version 6.11. Page generated on 2024-09-24 08:21 EST.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248
Kernel driver w83627ehf
=======================

Supported chips:

  * Winbond W83627EHF/EHG (ISA access ONLY)

    Prefix: 'w83627ehf'

    Addresses scanned: ISA address retrieved from Super I/O registers

    Datasheet: not available

  * Winbond W83627DHG

    Prefix: 'w83627dhg'

    Addresses scanned: ISA address retrieved from Super I/O registers

    Datasheet: not available

  * Winbond W83627DHG-P

    Prefix: 'w83627dhg'

    Addresses scanned: ISA address retrieved from Super I/O registers

    Datasheet: not available

  * Winbond W83627UHG

    Prefix: 'w83627uhg'

    Addresses scanned: ISA address retrieved from Super I/O registers

    Datasheet: available from www.nuvoton.com

  * Winbond W83667HG

    Prefix: 'w83667hg'

    Addresses scanned: ISA address retrieved from Super I/O registers

    Datasheet: not available

  * Winbond W83667HG-B

    Prefix: 'w83667hg'

    Addresses scanned: ISA address retrieved from Super I/O registers

    Datasheet: Available from Nuvoton upon request

  * Nuvoton NCT6775F/W83667HG-I

    Prefix: 'nct6775'

    Addresses scanned: ISA address retrieved from Super I/O registers

    Datasheet: Available from Nuvoton upon request

  * Nuvoton NCT6776F

    Prefix: 'nct6776'

    Addresses scanned: ISA address retrieved from Super I/O registers

    Datasheet: Available from Nuvoton upon request


Authors:

	- Jean Delvare <jdelvare@suse.de>
	- Yuan Mu (Winbond)
	- Rudolf Marek <r.marek@assembler.cz>
	- David Hubbard <david.c.hubbard@gmail.com>
	- Gong Jun <JGong@nuvoton.com>

Description
-----------

This driver implements support for the Winbond W83627EHF, W83627EHG,
W83627DHG, W83627DHG-P, W83627UHG, W83667HG, W83667HG-B, W83667HG-I
(NCT6775F), and NCT6776F super I/O chips. We will refer to them collectively
as Winbond chips.

The chips implement 3 to 4 temperature sensors (9 for NCT6775F and NCT6776F),
2 to 5 fan rotation speed sensors, 8 to 10 analog voltage sensors, one VID
(except for 627UHG), alarms with beep warnings (control unimplemented),
and some automatic fan regulation strategies (plus manual fan control mode).

The temperature sensor sources on W82677HG-B, NCT6775F, and NCT6776F are
configurable. temp4 and higher attributes are only reported if its temperature
source differs from the temperature sources of the already reported temperature
sensors. The configured source for each of the temperature sensors is provided
in tempX_label.

Temperatures are measured in degrees Celsius and measurement resolution is 1
degC for temp1 and 0.5 degC for temp2 and temp3. For temp4 and higher,
resolution is 1 degC for W83667HG-B and 0.0 degC for NCT6775F and NCT6776F.
An alarm is triggered when the temperature gets higher than high limit;
it stays on until the temperature falls below the hysteresis value.
Alarms are only supported for temp1, temp2, and temp3.

Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
triggered if the rotation speed has dropped below a programmable limit. Fan
readings can be divided by a programmable divider (1, 2, 4, 8, 16, 32, 64 or
128) to give the readings more range or accuracy. The driver sets the most
suitable fan divisor itself. Some fans might not be present because they
share pins with other functions.

Voltage sensors (also known as IN sensors) report their values in millivolts.
An alarm is triggered if the voltage has crossed a programmable minimum
or maximum limit.

The driver supports automatic fan control mode known as Thermal Cruise.
In this mode, the chip attempts to keep the measured temperature in a
predefined temperature range. If the temperature goes out of range, fan
is driven slower/faster to reach the predefined range again.

The mode works for fan1-fan4. Mapping of temperatures to pwm outputs is as
follows::

  temp1 -> pwm1
  temp2 -> pwm2
  temp3 -> pwm3 (not on 627UHG)
  prog  -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not
		 supported by the driver)

/sys files
----------

name
	this is a standard hwmon device entry, it contains the name of
	the device (see the prefix in the list of supported devices at
	the top of this file)

pwm[1-4]
	this file stores PWM duty cycle or DC value (fan speed) in range:

	   0 (stop) to 255 (full)

pwm[1-4]_enable
	this file controls mode of fan/temperature control:

	* 1 Manual mode, write to pwm file any value 0-255 (full speed)
	* 2 "Thermal Cruise" mode
	* 3 "Fan Speed Cruise" mode
	* 4 "Smart Fan III" mode
	* 5 "Smart Fan IV" mode

	SmartFan III mode is not supported on NCT6776F.

	SmartFan IV mode is configurable only if it was configured at system
	startup, and is only supported for W83677HG-B, NCT6775F, and NCT6776F.
	SmartFan IV operational parameters can not be configured at this time,
	and the various pwm attributes are not used in SmartFan IV mode.
	The attributes can be written to, which is useful if you plan to
	configure the system for a different pwm mode. However, the information
	returned when reading pwm attributes is unrelated to SmartFan IV
	operation.

pwm[1-4]_mode
	controls if output is PWM or DC level

	* 0 DC output (0 - 12v)
	* 1 PWM output

Thermal Cruise mode
-------------------

If the temperature is in the range defined by:

pwm[1-4]_target
		   set target temperature, unit millidegree Celsius
		   (range 0 - 127000)
pwm[1-4]_tolerance
		   tolerance, unit millidegree Celsius (range 0 - 15000)

there are no changes to fan speed. Once the temperature leaves the interval,
fan speed increases (temp is higher) or decreases if lower than desired.
There are defined steps and times, but not exported by the driver yet.

pwm[1-4]_min_output
		   minimum fan speed (range 1 - 255), when the temperature
		   is below defined range.
pwm[1-4]_stop_time
		   how many milliseconds [ms] must elapse to switch
		   corresponding fan off. (when the temperature was below
		   defined range).
pwm[1-4]_start_output
		   minimum fan speed (range 1 - 255) when spinning up
pwm[1-4]_step_output
		   rate of fan speed change (1 - 255)
pwm[1-4]_stop_output
		   minimum fan speed (range 1 - 255) when spinning down
pwm[1-4]_max_output
		   maximum fan speed (range 1 - 255), when the temperature
		   is above defined range.

Note: last six functions are influenced by other control bits, not yet exported
      by the driver, so a change might not have any effect.

Implementation Details
----------------------

Future driver development should bear in mind that the following registers have
different functions on the 627EHF and the 627DHG. Some registers also have
different power-on default values, but BIOS should already be loading
appropriate defaults. Note that bank selection must be performed as is currently
done in the driver for all register addresses.

========================= =====================================================
Register(s)		  Meaning
========================= =====================================================
0x49                      only on DHG, selects temperature source for AUX fan,
			  CPU fan0
0x4a                      not completely documented for the EHF and the DHG
			  documentation assigns different behavior to bits 7
			  and 6, including extending the temperature input
			  selection to SmartFan I, not just SmartFan III.
			  Testing on the EHF will reveal whether they are
			  compatible or not.
0x58                      Chip ID: 0xa1=EHF 0xc1=DHG
0x5e                      only on DHG, has bits to enable "current mode"
			  temperature detection and critical temperature
			  protection
0x45b                     only on EHF, bit 3, vin4 alarm (EHF supports 10
			  inputs, only 9 on DHG)
0x552                     only on EHF, vin4
0x558                     only on EHF, vin4 high limit
0x559                     only on EHF, vin4 low limit
0x6b                      only on DHG, SYS fan critical temperature
0x6c                      only on DHG, CPU fan0 critical temperature
0x6d                      only on DHG, AUX fan critical temperature
0x6e                      only on DHG, CPU fan1 critical temperature
0x50-0x55 and 0x650-0x657 marked as:

			    - "Test Register" for the EHF
			    - "Reserved Register" for the DHG
========================= =====================================================

The DHG also supports PECI, where the DHG queries Intel CPU temperatures, and
the ICH8 southbridge gets that data via PECI from the DHG, so that the
southbridge drives the fans. And the DHG supports SST, a one-wire serial bus.

The DHG-P has an additional automatic fan speed control mode named Smart Fan
(TM) III+. This mode is not yet supported by the driver.