Based on kernel version 6.11. Page generated on 2024-09-24 08:21 EST.
| 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 |
Kernel driver tps53679
======================
Supported chips:
* Texas Instruments TPS53647
Prefix: 'tps53647'
Addresses scanned: -
Datasheet: https://www.ti.com/lit/gpn/tps53647
* Texas Instruments TPS53667
Prefix: 'tps53667'
Addresses scanned: -
Datasheet: https://www.ti.com/lit/gpn/TPS53667
* Texas Instruments TPS53676
Prefix: 'tps53676'
Addresses scanned: -
Datasheet: https://www.ti.com/lit/gpn/TPS53676
* Texas Instruments TPS53679
Prefix: 'tps53679'
Addresses scanned: -
Datasheet: https://www.ti.com/lit/gpn/TPS53679 (short version)
* Texas Instruments TPS53681
Prefix: 'tps53681'
Addresses scanned: -
Datasheet: https://www.ti.com/lit/gpn/TPS53681
* Texas Instruments TPS53688
Prefix: 'tps53688'
Addresses scanned: -
Datasheet: Available under NDA
Authors:
Vadim Pasternak <vadimp@mellanox.com>
Guenter Roeck <linux@roeck-us.net>
Description
-----------
Chips in this series are multi-phase step-down converters with one or two
output channels and up to 8 phases per channel.
Usage Notes
-----------
This driver does not probe for PMBus devices. You will have to instantiate
devices explicitly.
Example: the following commands will load the driver for an TPS53681 at address
0x60 on I2C bus #1::
# modprobe tps53679
# echo tps53681 0x60 > /sys/bus/i2c/devices/i2c-1/new_device
Sysfs attributes
----------------
======================= ========================================================
in1_label "vin"
in1_input Measured input voltage.
in1_lcrit Critical minimum input voltage
TPS53679, TPS53681, TPS53688 only.
in1_lcrit_alarm Input voltage critical low alarm.
TPS53679, TPS53681, TPS53688 only.
in1_crit Critical maximum input voltage.
in1_crit_alarm Input voltage critical high alarm.
in[N]_label "vout[1-2]"
- TPS53647, TPS53667: N=2
- TPS53679, TPS53588: N=2,3
in[N]_input Measured output voltage.
in[N]_lcrit Critical minimum input voltage.
TPS53679, TPS53681, TPS53688 only.
in[N]_lcrit_alarm Critical minimum voltage alarm.
TPS53679, TPS53681, TPS53688 only.
in[N]_alarm Output voltage alarm.
TPS53647, TPS53667 only.
in[N]_crit Critical maximum output voltage.
TPS53679, TPS53681, TPS53688 only.
in[N]_crit_alarm Output voltage critical high alarm.
TPS53679, TPS53681, TPS53688 only.
temp[N]_input Measured temperature.
- TPS53647, TPS53667: N=1
- TPS53679, TPS53681, TPS53588: N=1,2
temp[N]_max Maximum temperature.
temp[N]_crit Critical high temperature.
temp[N]_max_alarm Temperature high alarm.
temp[N]_crit_alarm Temperature critical high alarm.
power1_label "pin".
power1_input Measured input power.
power[N]_label "pout[1-2]".
- TPS53647, TPS53667: N=2
- TPS53676, TPS53679, TPS53681, TPS53588: N=2,3
power[N]_input Measured output power.
curr1_label "iin".
curr1_input Measured input current.
curr1_max Maximum input current.
curr1_max_alarm Input current high alarm.
curr1_crit Critical input current.
curr1_crit_alarm Input current critical alarm.
curr[N]_label "iout[1-2]" or "iout1.[0-5]".
The first digit is the output channel, the second
digit is the phase within the channel. Per-phase
telemetry supported on TPS53676 and TPS53681 only.
- TPS53647, TPS53667: N=2
- TPS53679, TPS53588: N=2,3
- TPS53676: N=2-8
- TPS53681: N=2-9
curr[N]_input Measured output current.
curr[N]_max Maximum output current.
curr[N]_crit Critical high output current.
curr[N]_max_alarm Output current high alarm.
curr[N]_crit_alarm Output current critical high alarm.
Limit and alarm attributes are only available for
non-phase telemetry (iout1, iout2).
======================= ========================================================
|