Documentation / devicetree / bindings / mfd / rohm,bd71837-pmic.yaml


Based on kernel version 6.11. Page generated on 2024-09-24 08:21 EST.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
%YAML 1.2
---
$id: http://devicetree.org/schemas/mfd/rohm,bd71837-pmic.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: ROHM BD71837 Power Management Integrated Circuit

maintainers:
  - Matti Vaittinen <mazziesaccount@gmail.com>

description: |
  BD71837MWV is programmable Power Management ICs for powering single-core,
  dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is optimized for low
  BOM cost and compact solution footprint. BD71837MWV  integrates 8 Buck
  regulators and 7 LDOs.
  Datasheet for BD71837 is available at
  https://www.rohm.com/products/power-management/power-management-ic-for-system/industrial-consumer-applications/nxp-imx/bd71837amwv-product

properties:
  compatible:
    const: rohm,bd71837

  reg:
    description:
      I2C slave address.
    maxItems: 1

  interrupts:
    maxItems: 1

  clocks:
    maxItems: 1

  clock-names:
    const: osc
 
  "#clock-cells":
    const: 0

  clock-output-names:
    const: pmic_clk
 
# The BD718x7 supports two different HW states as reset target states. States
# are called as SNVS and READY. At READY state all the PMIC power outputs go
# down and OTP is reload. At the SNVS state all other logic and external
# devices apart from the SNVS power domain are shut off. Please refer to NXP
# i.MX8 documentation for further information regarding SNVS state. When a
# reset is done via SNVS state the PMIC OTP data is not reload. This causes
# power outputs that have been under SW control to stay down when reset has
# switched power state to SNVS. If reset is done via READY state the power
# outputs will be returned to HW control by OTP loading. Thus the reset
# target state is set to READY by default. If SNVS state is used the boot
# crucial regulators must have the regulator-always-on and regulator-boot-on
# properties set in regulator node.

  rohm,reset-snvs-powered:
    description: |
      Transfer PMIC to SNVS state at reset
    type: boolean
 
# Configure the "short press" and "long press" timers for the power button.
# Values are rounded to what hardware supports
# Short-press:
#   Shortest being 10ms, next 500ms and then multiple of 500ms up to 7,5s
# Long-press:
#   Shortest being 10ms, next 1000ms and then multiple of 1000ms up to 15s
# If these properties are not present the existing configuration (from
# bootloader or OTP) is not touched.

  rohm,short-press-ms:
    description:
      Short press duration in milliseconds
    enum:
      - 10
      - 500
      - 1000
      - 1500
      - 2000
      - 2500
      - 3000
      - 3500
      - 4000
      - 4500
      - 5000
      - 5500
      - 6000
      - 6500
      - 7000

  rohm,long-press-ms:
    description:
      Long press duration in milliseconds
    enum:
      - 10
      - 1000
      - 2000
      - 3000
      - 4000
      - 5000
      - 6000
      - 7000
      - 8000
      - 9000
      - 10000
      - 11000
      - 12000
      - 13000
      - 14000

  regulators:
    $ref: /schemas/regulator/rohm,bd71837-regulator.yaml
    description:
      List of child nodes that specify the regulators.

required:
  - compatible
  - reg
  - interrupts
  - clocks
  - "#clock-cells"
  - regulators

additionalProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/irq.h>
    #include <dt-bindings/leds/common.h>
 
    i2c {
        #address-cells = <1>;
        #size-cells = <0>;
        pmic: pmic@4b {
            compatible = "rohm,bd71837";
            reg = <0x4b>;
            interrupt-parent = <&gpio1>;
            interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
            #clock-cells = <0>;
            clocks = <&osc 0>;
            rohm,reset-snvs-powered;
            rohm,short-press-ms = <10>;
            rohm,long-press-ms = <2000>;
 
            regulators {
                buck1: BUCK1 {
                    regulator-name = "buck1";
                    regulator-min-microvolt = <700000>;
                    regulator-max-microvolt = <1300000>;
                    regulator-boot-on;
                    regulator-always-on;
                    regulator-ramp-delay = <1250>;
                    rohm,dvs-run-voltage = <900000>;
                    rohm,dvs-idle-voltage = <850000>;
                    rohm,dvs-suspend-voltage = <800000>;
                };
                buck2: BUCK2 {
                    regulator-name = "buck2";
                    regulator-min-microvolt = <700000>;
                    regulator-max-microvolt = <1300000>;
                    regulator-boot-on;
                    regulator-always-on;
                    regulator-ramp-delay = <1250>;
                    rohm,dvs-run-voltage = <1000000>;
                    rohm,dvs-idle-voltage = <900000>;
                };
                buck3: BUCK3 {
                    regulator-name = "buck3";
                    regulator-min-microvolt = <700000>;
                    regulator-max-microvolt = <1300000>;
                    regulator-boot-on;
                    rohm,dvs-run-voltage = <1000000>;
                };
                buck4: BUCK4 {
                    regulator-name = "buck4";
                    regulator-min-microvolt = <700000>;
                    regulator-max-microvolt = <1300000>;
                    regulator-boot-on;
                    rohm,dvs-run-voltage = <1000000>;
                };
                buck5: BUCK5 {
                    regulator-name = "buck5";
                    regulator-min-microvolt = <700000>;
                    regulator-max-microvolt = <1350000>;
                    regulator-boot-on;
                };
                buck6: BUCK6 {
                    regulator-name = "buck6";
                    regulator-min-microvolt = <3000000>;
                    regulator-max-microvolt = <3300000>;
                    regulator-boot-on;
                };
                buck7: BUCK7 {
                    regulator-name = "buck7";
                    regulator-min-microvolt = <1605000>;
                    regulator-max-microvolt = <1995000>;
                    regulator-boot-on;
                };
                buck8: BUCK8 {
                    regulator-name = "buck8";
                    regulator-min-microvolt = <800000>;
                    regulator-max-microvolt = <1400000>;
                };
 
                ldo1: LDO1 {
                    regulator-name = "ldo1";
                    regulator-min-microvolt = <3000000>;
                    regulator-max-microvolt = <3300000>;
                    regulator-boot-on;
                };
                ldo2: LDO2 {
                    regulator-name = "ldo2";
                    regulator-min-microvolt = <900000>;
                    regulator-max-microvolt = <900000>;
                    regulator-boot-on;
                };
                ldo3: LDO3 {
                    regulator-name = "ldo3";
                    regulator-min-microvolt = <1800000>;
                    regulator-max-microvolt = <3300000>;
                };
                ldo4: LDO4 {
                    regulator-name = "ldo4";
                    regulator-min-microvolt = <900000>;
                    regulator-max-microvolt = <1800000>;
                };
                ldo5: LDO5 {
                    regulator-name = "ldo5";
                    regulator-min-microvolt = <1800000>;
                    regulator-max-microvolt = <3300000>;
                };
                ldo6: LDO6 {
                    regulator-name = "ldo6";
                    regulator-min-microvolt = <900000>;
                    regulator-max-microvolt = <1800000>;
                };
                ldo7_reg: LDO7 {
                    regulator-name = "ldo7";
                    regulator-min-microvolt = <1800000>;
                    regulator-max-microvolt = <3300000>;
                };
            };
        };
    };