Documentation / devicetree / bindings / mfd / rohm,bd9571mwv.yaml


Based on kernel version 6.11. Page generated on 2024-09-24 08:21 EST.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/mfd/rohm,bd9571mwv.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: ROHM BD9571MWV/BD9574MWF Power Management Integrated Circuit (PMIC)

maintainers:
  - Marek Vasut <marek.vasut@gmail.com>

properties:
  compatible:
    enum:
      - rohm,bd9571mwv
      - rohm,bd9574mwf

  reg:
    maxItems: 1

  interrupts:
    maxItems: 1

  interrupt-controller: true
 
  '#interrupt-cells':
    const: 2

  gpio-controller: true
 
  '#gpio-cells':
    const: 2

  rohm,ddr-backup-power:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0x0
    maximum: 0xf
    description: |
      Value to use for DDR-Backup Power (default 0).
      This is a bitmask that specifies which DDR power rails need to be kept
      powered when backup mode is entered, for system suspend:
        - bit 0: DDR0
        - bit 1: DDR1
        - bit 2: DDR0C
        - bit 3: DDR1C
      These bits match the KEEPON_DDR* bits in the documentation for the "BKUP
      Mode Cnt" register.

  rohm,rstbmode-level:
    $ref: /schemas/types.yaml#/definitions/flag
    description:
      The RSTB signal is configured for level mode, to accommodate a toggle
      power switch (the RSTBMODE pin is strapped low).

  rohm,rstbmode-pulse:
    $ref: /schemas/types.yaml#/definitions/flag
    description:
      The RSTB signal is configured for pulse mode, to accommodate a momentary
      power switch (the RSTBMODE pin is strapped high).

  regulators:
    type: object
    description:
      List of child nodes that specify the regulator initialization data.
      Child nodes must be named after their hardware counterparts.

    patternProperties:
      "^(vd09|vd18|vd25|vd33|dvfs)$":
        type: object
        $ref: /schemas/regulator/regulator.yaml#

        properties:
          regulator-name:
            pattern: "^(vd09|vd18|vd25|vd33|dvfs)$"

        unevaluatedProperties: false

    additionalProperties: false

additionalProperties: false

required:
  - compatible
  - reg
  - interrupts
  - interrupt-controller
  - '#interrupt-cells'
  - gpio-controller
  - '#gpio-cells'

oneOf:
  - required:
      - rohm,rstbmode-level
  - required:
      - rohm,rstbmode-pulse

examples:
  - |
    #include <dt-bindings/interrupt-controller/irq.h>
 
    i2c {
          #address-cells = <1>;
          #size-cells = <0>;
 
          pmic: pmic@30 {
                  compatible = "rohm,bd9571mwv";
                  reg = <0x30>;
                  interrupt-parent = <&gpio2>;
                  interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
                  interrupt-controller;
                  #interrupt-cells = <2>;
                  gpio-controller;
                  #gpio-cells = <2>;
                  rohm,ddr-backup-power = <0xf>;
                  rohm,rstbmode-pulse;
 
                  regulators {
                          dvfs: dvfs {
                                  regulator-name = "dvfs";
                                  regulator-min-microvolt = <750000>;
                                  regulator-max-microvolt = <1030000>;
                                  regulator-boot-on;
                                  regulator-always-on;
                          };
                  };
          };
    };