# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/mmc/mtk-sd.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: MTK MSDC Storage Host Controller

maintainers:
  - Chaotian Jing <chaotian.jing@mediatek.com>
  - Wenbin Mei <wenbin.mei@mediatek.com>

properties:
  compatible:
    oneOf:
      - enum:
          - mediatek,mt2701-mmc
          - mediatek,mt2712-mmc
          - mediatek,mt6779-mmc
          - mediatek,mt6795-mmc
          - mediatek,mt7620-mmc
          - mediatek,mt7622-mmc
          - mediatek,mt7986-mmc
          - mediatek,mt8135-mmc
          - mediatek,mt8173-mmc
          - mediatek,mt8183-mmc
          - mediatek,mt8516-mmc
      - items:
          - const: mediatek,mt7623-mmc
          - const: mediatek,mt2701-mmc
      - items:
          - enum:
              - mediatek,mt8186-mmc
              - mediatek,mt8188-mmc
              - mediatek,mt8192-mmc
              - mediatek,mt8195-mmc
              - mediatek,mt8365-mmc
          - const: mediatek,mt8183-mmc

  reg:
    minItems: 1
    items:
      - description: base register (required).
      - description: top base register (required for MT8183).

  clocks:
    description:
      Should contain phandle for the clock feeding the MMC controller.
    minItems: 2
    maxItems: 7

  clock-names:
    minItems: 2
    maxItems: 7

  interrupts:
    description:
      Should at least contain MSDC GIC interrupt. To support SDIO in-band wakeup, an extended
      interrupt is required and be configured as wakeup source irq.
    minItems: 1
    maxItems: 2

  interrupt-names:
    items:
      - const: msdc
      - const: sdio_wakeup

  pinctrl-names:
    description:
      Should at least contain default and state_uhs. To support SDIO in-band wakeup, dat1 pin
      will be switched between GPIO mode and SDIO DAT1 mode, state_eint is mandatory in this
      scenario.
    minItems: 2
    items:
      - const: default
      - const: state_uhs
      - const: state_eint

  pinctrl-0:
    description:
      should contain default/high speed pin ctrl.
    maxItems: 1

  pinctrl-1:
    description:
      should contain uhs mode pin ctrl.
    maxItems: 1

  pinctrl-2:
    description:
      should switch dat1 pin to GPIO mode.
    maxItems: 1

  hs400-ds-delay:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      HS400 DS delay setting.
    minimum: 0
    maximum: 0xffffffff

  mediatek,hs200-cmd-int-delay:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      HS200 command internal delay setting.
      This field has total 32 stages.
      The value is an integer from 0 to 31.
    minimum: 0
    maximum: 31

  mediatek,hs400-cmd-int-delay:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      HS400 command internal delay setting.
      This field has total 32 stages.
      The value is an integer from 0 to 31.
    minimum: 0
    maximum: 31

  mediatek,hs400-cmd-resp-sel-rising:
    $ref: /schemas/types.yaml#/definitions/flag
    description:
      HS400 command response sample selection.
      If present, HS400 command responses are sampled on rising edges.
      If not present, HS400 command responses are sampled on falling edges.

  mediatek,hs400-ds-dly3:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      Gear of the third delay line for DS for input data latch in data
      pad macro, there are 32 stages from 0 to 31.
      For different corner IC, the time is different about one step, it is
      about 100ps.
      The value is confirmed by doing scan and calibration to find a best
      value with corner IC and it is valid only for HS400 mode.
    minimum: 0
    maximum: 31

  mediatek,latch-ck:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      Some SoCs do not support enhance_rx, need set correct latch-ck to avoid
      data crc error caused by stop clock(fifo full) Valid range = [0:0x7].
      if not present, default value is 0.
      applied to compatible "mediatek,mt2701-mmc".
    minimum: 0
    maximum: 7

  mediatek,tuning-step:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      Some SoCs need extend tuning step for better delay value to avoid CRC issue.
      If not present, default tuning step is 32. For eMMC and SD, this can yield
      satisfactory calibration results in most cases.
    enum: [32, 64]
    default: 32

  resets:
    maxItems: 1

  reset-names:
    const: hrst

required:
  - compatible
  - reg
  - interrupts
  - clocks
  - clock-names
  - pinctrl-names
  - pinctrl-0
  - pinctrl-1
  - vmmc-supply
  - vqmmc-supply

allOf:
  - $ref: mmc-controller.yaml#
  - if:
      properties:
        compatible:
          enum:
            - mediatek,mt2701-mmc
            - mediatek,mt6779-mmc
            - mediatek,mt6795-mmc
            - mediatek,mt7620-mmc
            - mediatek,mt7622-mmc
            - mediatek,mt7623-mmc
            - mediatek,mt8135-mmc
            - mediatek,mt8173-mmc
            - mediatek,mt8183-mmc
            - mediatek,mt8186-mmc
            - mediatek,mt8188-mmc
            - mediatek,mt8195-mmc
            - mediatek,mt8516-mmc
    then:
      properties:
        clocks:
          minItems: 2
          items:
            - description: source clock
            - description: HCLK which used for host
            - description: independent source clock gate
        clock-names:
          minItems: 2
          items:
            - const: source
            - const: hclk
            - const: source_cg

  - if:
      properties:
        compatible:
          contains:
            const: mediatek,mt2712-mmc
    then:
      properties:
        clocks:
          minItems: 3
          items:
            - description: source clock
            - description: HCLK which used for host
            - description: independent source clock gate
            - description: bus clock used for internal register access (required for MSDC0/3).
        clock-names:
          minItems: 3
          items:
            - const: source
            - const: hclk
            - const: source_cg
            - const: bus_clk

  - if:
      properties:
        compatible:
          contains:
            const: mediatek,mt8183-mmc
    then:
      properties:
        reg:
          minItems: 2

  - if:
      properties:
        compatible:
          contains:
            enum:
              - mediatek,mt7986-mmc
    then:
      properties:
        clocks:
          minItems: 3
          items:
            - description: source clock
            - description: HCLK which used for host
            - description: independent source clock gate
            - description: bus clock used for internal register access (required for MSDC0/3).
            - description: msdc subsys clock gate
        clock-names:
          minItems: 3
          items:
            - const: source
            - const: hclk
            - const: source_cg
            - const: bus_clk
            - const: sys_cg

  - if:
      properties:
        compatible:
          enum:
            - mediatek,mt8186-mmc
            - mediatek,mt8188-mmc
            - mediatek,mt8195-mmc
    then:
      properties:
        clocks:
          items:
            - description: source clock
            - description: HCLK which used for host
            - description: independent source clock gate
            - description: crypto clock used for data encrypt/decrypt (optional)
        clock-names:
          items:
            - const: source
            - const: hclk
            - const: source_cg
            - const: crypto

  - if:
      properties:
        compatible:
          contains:
            const: mediatek,mt8192-mmc
    then:
      properties:
        clocks:
          items:
            - description: source clock
            - description: HCLK which used for host
            - description: independent source clock gate
            - description: msdc subsys clock gate
            - description: peripheral bus clock gate
            - description: AXI bus clock gate
            - description: AHB bus clock gate
        clock-names:
          items:
            - const: source
            - const: hclk
            - const: source_cg
            - const: sys_cg
            - const: pclk_cg
            - const: axi_cg
            - const: ahb_cg

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/irq.h>
    #include <dt-bindings/interrupt-controller/arm-gic.h>
    #include <dt-bindings/clock/mt8173-clk.h>
    mmc0: mmc@11230000 {
        compatible = "mediatek,mt8173-mmc";
        reg = <0x11230000 0x1000>;
        interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>;
        vmmc-supply = <&mt6397_vemc_3v3_reg>;
        vqmmc-supply = <&mt6397_vio18_reg>;
        clocks = <&pericfg CLK_PERI_MSDC30_0>,
                 <&topckgen CLK_TOP_MSDC50_0_H_SEL>;
        clock-names = "source", "hclk";
        pinctrl-names = "default", "state_uhs";
        pinctrl-0 = <&mmc0_pins_default>;
        pinctrl-1 = <&mmc0_pins_uhs>;
        assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
        assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
        hs400-ds-delay = <0x14015>;
        mediatek,hs200-cmd-int-delay = <26>;
        mediatek,hs400-cmd-int-delay = <14>;
        mediatek,hs400-cmd-resp-sel-rising;
    };
 
    mmc3: mmc@11260000 {
        compatible = "mediatek,mt8173-mmc";
        reg = <0x11260000 0x1000>;
        clock-names = "source", "hclk";
        clocks = <&pericfg CLK_PERI_MSDC30_3>,
                 <&topckgen CLK_TOP_MSDC50_2_H_SEL>;
        interrupt-names = "msdc", "sdio_wakeup";
        interrupts-extended = <&gic GIC_SPI 74 IRQ_TYPE_LEVEL_LOW 0>,
                     <&pio 23 IRQ_TYPE_LEVEL_LOW>;
        pinctrl-names = "default", "state_uhs", "state_eint";
        pinctrl-0 = <&mmc2_pins_default>;
        pinctrl-1 = <&mmc2_pins_uhs>;
        pinctrl-2 = <&mmc2_pins_eint>;
        bus-width = <4>;
        max-frequency = <200000000>;
        cap-sd-highspeed;
        sd-uhs-sdr104;
        keep-power-in-suspend;
        wakeup-source;
        cap-sdio-irq;
        no-mmc;
        no-sd;
        non-removable;
        vmmc-supply = <&sdio_fixed_3v3>;
        vqmmc-supply = <&mt6397_vgp3_reg>;
        mmc-pwrseq = <&wifi_pwrseq>;
    };

...