# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/display/bridge/adi,adv7511.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Analog Devices ADV7511/11W/13 HDMI Encoders

maintainers:
  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>

description: |
  The ADV7511, ADV7511W and ADV7513 are HDMI audio and video
  transmitters compatible with HDMI 1.4 and DVI 1.0. They support color
  space conversion, S/PDIF, CEC and HDCP. The transmitter input is
  parallel RGB or YUV data.

properties:
  compatible:
    enum:
      - adi,adv7511
      - adi,adv7511w
      - adi,adv7513

  reg:
    description: |
      I2C slave addresses.
 
      The ADV7511/11W/13 internal registers are split into four pages
      exposed through different I2C addresses, creating four register
      maps. Each map has it own I2C address and acts as a standard slave
      device on the I2C bus. The main address is mandatory, others are
      optional and revert to defaults if not specified.
    minItems: 1
    maxItems: 4

  reg-names:
    description:
      Names of maps with programmable addresses. It can contain any map
      needing a non-default address.
    minItems: 1
    items:
      - const: main
      - const: edid
      - const: cec
      - const: packet

  clocks:
    description: Reference to the CEC clock.
    maxItems: 1

  clock-names:
    const: cec

  interrupts:
    maxItems: 1

  pd-gpios:
    description: GPIO connected to the power down signal.
    maxItems: 1

  avdd-supply:
    description: A 1.8V supply that powers up the AVDD pin.

  dvdd-supply:
    description: A 1.8V supply that powers up the DVDD pin.

  pvdd-supply:
    description: A 1.8V supply that powers up the PVDD pin.

  dvdd-3v-supply:
    description: A 3.3V supply that powers up the DVDD_3V pin.

  bgvdd-supply:
    description: A 1.8V supply that powers up the BGVDD pin.

  adi,input-depth:
    description: Number of bits per color component at the input.
    $ref: /schemas/types.yaml#/definitions/uint32
    enum: [ 8, 10, 12 ]

  adi,input-colorspace:
    description: Input color space.
    enum: [ rgb, yuv422, yuv444 ]

  adi,input-clock:
    description: |
      Input clock type.
        "1x": one clock cycle per pixel
        "2x": two clock cycles per pixel
        "dd": one clock cycle per pixel, data driven on both edges
    enum: [ 1x, 2x, dd ]

  adi,clock-delay:
    description:
      Video data clock delay relative to the pixel clock, in ps
      (-1200ps .. 1600 ps).
    $ref: /schemas/types.yaml#/definitions/uint32
    default: 0

  adi,embedded-sync:
    description:
      If defined, the input uses synchronization signals embedded in the
      data stream (similar to BT.656).
    type: boolean

  adi,input-style:
    description:
      Input components arrangement variant as listed in the input
      format tables in the datasheet.
    $ref: /schemas/types.yaml#/definitions/uint32
    enum: [ 1, 2, 3 ]

  adi,input-justification:
    description: Input bit justification.
    enum: [ left, evenly, right ]

  ports:
    description:
      The ADV7511(W)/13 has two video ports and one audio port.
    $ref: /schemas/graph.yaml#/properties/ports

    properties:
      port@0:
        description: Video port for the RGB or YUV input.
        $ref: /schemas/graph.yaml#/properties/port

      port@1:
        description: Video port for the HDMI output.
        $ref: /schemas/graph.yaml#/properties/port

      port@2:
        description: Audio port for the HDMI output.
        $ref: /schemas/graph.yaml#/properties/port
 
# adi,input-colorspace and adi,input-clock are required except in
# "rgb 1x" and "yuv444 1x" modes, in which case they must not be
# specified.
if:
  not:
    properties:
      adi,input-colorspace:
        contains:
          enum: [ rgb, yuv444 ]
      adi,input-clock:
        contains:
          const: 1x

then:
  required:
    - adi,input-style
    - adi,input-justification

else:
  properties:
    adi,input-style: false
    adi,input-justification: false
 

required:
  - compatible
  - reg
  - ports
  - adi,input-depth
  - adi,input-colorspace
  - adi,input-clock
  - avdd-supply
  - dvdd-supply
  - pvdd-supply
  - dvdd-3v-supply
  - bgvdd-supply

additionalProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/irq.h>
 
    i2c@e6500000 {
        #address-cells = <1>;
        #size-cells = <0>;
 
        reg = <0 0xe6500000>;
 
        adv7511w: hdmi@39 {
            compatible = "adi,adv7511w";
            /*
             * The EDID page will be accessible on address 0x66 on the I2C
             * bus. All other maps continue to use their default addresses.
             */
            reg = <0x39>, <0x66>;
            reg-names = "main", "edid";
            interrupt-parent = <&gpio3>;
            interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
            clocks = <&cec_clock>;
            clock-names = "cec";
            avdd-supply = <&v1v8>;
            dvdd-supply = <&v1v8>;
            pvdd-supply = <&v1v8>;
            dvdd-3v-supply = <&v3v3>;
            bgvdd-supply = <&v1v8>;
 
            adi,input-depth = <8>;
            adi,input-colorspace = "yuv422";
            adi,input-clock = "1x";
 
            adi,input-style = <3>;
            adi,input-justification = "right";
            ports {
                #address-cells = <1>;
                #size-cells = <0>;
 
                port@0 {
                    reg = <0>;
                    adv7511w_in: endpoint {
                        remote-endpoint = <&dpi_out>;
                    };
                };
 
                port@1 {
                    reg = <1>;
                    adv7511_out: endpoint {
                        remote-endpoint = <&hdmi_connector_in>;
                    };
                };
 
                port@2 {
                    reg = <2>;
                    codec_endpoint: endpoint {
                        remote-endpoint = <&i2s0_cpu_endpoint>;
                    };
                };
            };
        };
    };

...