# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/input/touchscreen/cypress,cy8ctma340.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Cypress CY8CTMA340 series touchscreen controller

description: The Cypress CY8CTMA340 series (also known as "CYTTSP" after
  the marketing name Cypress TrueTouch Standard Product) touchscreens can
  be connected to either I2C or SPI buses.

maintainers:
  - Javier Martinez Canillas <javier@dowhile0.org>
  - Linus Walleij <linus.walleij@linaro.org>

allOf:
  - $ref: touchscreen.yaml#

properties:
  $nodename:
    pattern: "^touchscreen(@.*)?$"

  compatible:
    oneOf:
      - const: cypress,cy8ctma340
      - const: cypress,cy8ctst341
      - const: cypress,cyttsp-spi
        description: Legacy compatible for SPI connected CY8CTMA340
        deprecated: true
      - const: cypress,cyttsp-i2c
        description: Legacy compatible for I2C connected CY8CTMA340
        deprecated: true

  reg:
    description: I2C address when used on the I2C bus, or the SPI chip
      select index when used on the SPI bus

  clock-frequency:
    description: I2C client clock frequency, defined for host when using
      the device on the I2C bus
    minimum: 0
    maximum: 400000

  spi-max-frequency:
    description: SPI clock frequency, defined for host, defined when using
      the device on the SPI bus. The throughput is maximum 2 Mbps so the
      typical value is 2000000, if higher rates are used the total throughput
      needs to be restricted to 2 Mbps.
    minimum: 0
    maximum: 6000000

  interrupts:
    description: Interrupt to host
    maxItems: 1

  vcpin-supply:
    description: Analog power supply regulator on VCPIN pin

  vdd-supply:
    description: Digital power supply regulator on VDD pin

  reset-gpios:
    description: Reset line for the touchscreen, should be tagged
      as GPIO_ACTIVE_LOW

  bootloader-key:
    description: the 8-byte bootloader key that is required to switch
      the chip from bootloader mode (default mode) to application mode
    $ref: /schemas/types.yaml#/definitions/uint8-array
    minItems: 8
    maxItems: 8

  touchscreen-size-x: true
  touchscreen-size-y: true
  touchscreen-fuzz-x: true
  touchscreen-fuzz-y: true

  active-distance:
    description: the distance in pixels beyond which a touch must move
      before movement is detected and reported by the device
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 15

  active-interval-ms:
    description: the minimum period in ms between consecutive
      scanning/processing cycles when the chip is in active mode
    minimum: 0
    maximum: 255

  lowpower-interval-ms:
    description: the minimum period in ms between consecutive
      scanning/processing cycles when the chip is in low-power mode
    minimum: 0
    maximum: 2550

  touch-timeout-ms:
    description: minimum time in ms spent in the active power state while no
      touches are detected before entering low-power mode
    minimum: 0
    maximum: 2550

  use-handshake:
    description: enable register-based handshake (boolean). This should only
      be used if the chip is configured to use 'blocking communication with
      timeout' (in this case the device generates an interrupt at the end of
      every scanning/processing cycle)
    $ref: /schemas/types.yaml#/definitions/flag

additionalProperties: false

required:
  - compatible
  - reg
  - interrupts
  - bootloader-key
  - touchscreen-size-x
  - touchscreen-size-y

examples:
  - |
    #include <dt-bindings/interrupt-controller/irq.h>
    #include <dt-bindings/gpio/gpio.h>
    spi {
      #address-cells = <1>;
      #size-cells = <0>;
      num-cs = <1>;
      cs-gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
 
      touchscreen@0 {
        compatible = "cypress,cy8ctma340";
        reg = <0>;
        interrupt-parent = <&gpio>;
        interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
        reset-gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
        vdd-supply = <&ldo_aux1_reg>;
        vcpin-supply = <&ldo_aux2_reg>;
        bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
        touchscreen-size-x = <480>;
        touchscreen-size-y = <800>;
        active-interval-ms = <0>;
        touch-timeout-ms = <255>;
        lowpower-interval-ms = <10>;
      };
    };

...