Based on kernel version 5.8. Page generated on 2020-08-08 17:40 EST.
| 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 |
Binding for TI/National Semiconductor LP55xx Led Drivers
Required properties:
- compatible: one of
national,lp5521
national,lp5523
ti,lp55231
ti,lp5562
ti,lp8501
- reg: I2C slave address
- clock-mode: Input clock mode, (0: automode, 1: internal, 2: external)
Each child has own specific current settings
- led-cur: Current setting at each led channel (mA x10, 0 if led is not connected)
- max-cur: Maximun current at each led channel.
Optional properties:
- enable-gpio: GPIO attached to the chip's enable pin
- label: Used for naming LEDs
- pwr-sel: LP8501 specific property. Power selection for output channels.
0: D1~9 are connected to VDD
1: D1~6 with VDD, D7~9 with VOUT
2: D1~6 with VOUT, D7~9 with VDD
3: D1~9 are connected to VOUT
Alternatively, each child can have a specific channel name and trigger:
- chan-name (optional): name of channel
- linux,default-trigger (optional): see
Documentation/devicetree/bindings/leds/common.txt
example 1) LP5521
3 LED channels, external clock used. Channel names are 'lp5521_pri:channel0',
'lp5521_pri:channel1' and 'lp5521_pri:channel2', with a heartbeat trigger
on channel 0.
lp5521@32 {
compatible = "national,lp5521";
reg = <0x32>;
label = "lp5521_pri";
clock-mode = /bits/ 8 <2>;
chan0 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
linux,default-trigger = "heartbeat";
};
chan1 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
};
chan2 {
led-cur = /bits/ 8 <0x2f>;
max-cur = /bits/ 8 <0x5f>;
};
};
example 2) LP5523
9 LED channels with specific name. Internal clock used.
The I2C slave address is configurable with ASEL1 and ASEL0 pins.
Available addresses are 32/33/34/35h.
ASEL1 ASEL0 Address
-------------------------
GND GND 32h
GND VEN 33h
VEN GND 34h
VEN VEN 35h
lp5523@32 {
compatible = "national,lp5523";
reg = <0x32>;
clock-mode = /bits/ 8 <1>;
chan0 {
chan-name = "d1";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan1 {
chan-name = "d2";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan2 {
chan-name = "d3";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan3 {
chan-name = "d4";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan4 {
chan-name = "d5";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan5 {
chan-name = "d6";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan6 {
chan-name = "d7";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan7 {
chan-name = "d8";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan8 {
chan-name = "d9";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
};
example 3) LP5562
4 channels are defined.
lp5562@30 {
compatible = "ti,lp5562";
reg = <0x30>;
clock-mode = /bits/8 <2>;
chan0 {
chan-name = "R";
led-cur = /bits/ 8 <0x20>;
max-cur = /bits/ 8 <0x60>;
};
chan1 {
chan-name = "G";
led-cur = /bits/ 8 <0x20>;
max-cur = /bits/ 8 <0x60>;
};
chan2 {
chan-name = "B";
led-cur = /bits/ 8 <0x20>;
max-cur = /bits/ 8 <0x60>;
};
chan3 {
chan-name = "W";
led-cur = /bits/ 8 <0x20>;
max-cur = /bits/ 8 <0x60>;
};
};
example 4) LP8501
9 channels are defined. The 'pwr-sel' is LP8501 specific property.
Others are same as LP5523.
lp8501@32 {
compatible = "ti,lp8501";
reg = <0x32>;
clock-mode = /bits/ 8 <2>;
pwr-sel = /bits/ 8 <3>; /* D1~9 connected to VOUT */
chan0 {
chan-name = "d1";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan1 {
chan-name = "d2";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan2 {
chan-name = "d3";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan3 {
chan-name = "d4";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan4 {
chan-name = "d5";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan5 {
chan-name = "d6";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan6 {
chan-name = "d7";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan7 {
chan-name = "d8";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
chan8 {
chan-name = "d9";
led-cur = /bits/ 8 <0x14>;
max-cur = /bits/ 8 <0x20>;
};
};
|