Based on kernel version 4.13.3. Page generated on 2017-09-23 13:56 EST.
1 Documentation for CMI 8330 (SoundPRO) 2 ------------------------------------- 3 Alessandro Zummo <azummo@ita.flashnet.it> 4 5 ( Be sure to read Documentation/sound/oss/SoundPro too ) 6 7 8 This adapter is now directly supported by the sb driver. 9 10 The only thing you have to do is to compile the kernel sound 11 support as a module and to enable kernel ISAPnP support, 12 as shown below. 13 14 15 CONFIG_SOUND=m 16 CONFIG_SOUND_SB=m 17 18 CONFIG_PNP=y 19 CONFIG_ISAPNP=y 20 21 22 and optionally: 23 24 25 CONFIG_SOUND_MPU401=m 26 27 for MPU401 support. 28 29 30 (I suggest you to use "make menuconfig" or "make xconfig" 31 for a more comfortable configuration editing) 32 33 34 35 Then you can do 36 37 modprobe sb 38 39 and everything will be (hopefully) configured. 40 41 You should get something similar in syslog: 42 43 sb: CMI8330 detected. 44 sb: CMI8330 sb base located at 0x220 45 sb: CMI8330 mpu base located at 0x330 46 sb: CMI8330 mail reports to Alessandro Zummo <azummo@ita.flashnet.it> 47 sb: ISAPnP reports CMI 8330 SoundPRO at i/o 0x220, irq 7, dma 1,5 48 49 50 51 52 The old documentation file follows for reference 53 purposes. 54 55 56 How to enable CMI 8330 (SOUNDPRO) soundchip on Linux 57 ------------------------------------------ 58 Stefan Laudat <Stefan.Laudat@asit.ro> 59 60 [Note: The CMI 8338 is unrelated and is supported by cmpci.o] 61 62 63 In order to use CMI8330 under Linux you just have to use a proper isapnp.conf, a good isapnp and a little bit of patience. I use isapnp 1.17, but 64 you may get a better one I guess at http://www.roestock.demon.co.uk/isapnptools/. 65 66 Of course you will have to compile kernel sound support as module, as shown below: 67 68 CONFIG_SOUND=m 69 CONFIG_SOUND_OSS=m 70 CONFIG_SOUND_SB=m 71 CONFIG_SOUND_ADLIB=m 72 CONFIG_SOUND_MPU401=m 73 # Mikro$chaft sound system (kinda useful here ;)) 74 CONFIG_SOUND_MSS=m 75 76 The /etc/isapnp.conf file will be: 77 78 <snip below> 79 80 81 (READPORT 0x0203) 82 (ISOLATE PRESERVE) 83 (IDENTIFY *) 84 (VERBOSITY 2) 85 (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING 86 (VERIFYLD N) 87 88 89 # WSS 90 91 (CONFIGURE CMI0001/16777472 (LD 0 92 (IO 0 (SIZE 8) (BASE 0x0530)) 93 (IO 1 (SIZE 8) (BASE 0x0388)) 94 (INT 0 (IRQ 7 (MODE +E))) 95 (DMA 0 (CHANNEL 0)) 96 (NAME "CMI0001/16777472[0]{CMI8330/C3D Audio Adapter}") 97 (ACT Y) 98 )) 99 100 # MPU 101 102 (CONFIGURE CMI0001/16777472 (LD 1 103 (IO 0 (SIZE 2) (BASE 0x0330)) 104 (INT 0 (IRQ 11 (MODE +E))) 105 (NAME "CMI0001/16777472[1]{CMI8330/C3D Audio Adapter}") 106 (ACT Y) 107 )) 108 109 # Joystick 110 111 (CONFIGURE CMI0001/16777472 (LD 2 112 (IO 0 (SIZE 8) (BASE 0x0200)) 113 (NAME "CMI0001/16777472[2]{CMI8330/C3D Audio Adapter}") 114 (ACT Y) 115 )) 116 117 # SoundBlaster 118 119 (CONFIGURE CMI0001/16777472 (LD 3 120 (IO 0 (SIZE 16) (BASE 0x0220)) 121 (INT 0 (IRQ 5 (MODE +E))) 122 (DMA 0 (CHANNEL 1)) 123 (DMA 1 (CHANNEL 5)) 124 (NAME "CMI0001/16777472[3]{CMI8330/C3D Audio Adapter}") 125 (ACT Y) 126 )) 127 128 129 (WAITFORKEY) 130 131 <end of snip> 132 133 The module sequence is trivial: 134 135 /sbin/insmod soundcore 136 /sbin/insmod sound 137 /sbin/insmod uart401 138 # insert this first 139 /sbin/insmod ad1848 io=0x530 irq=7 dma=0 soundpro=1 140 # The sb module is an alternative to the ad1848 (Microsoft Sound System) 141 # Anyhow, this is full duplex and has MIDI 142 /sbin/insmod sb io=0x220 dma=1 dma16=5 irq=5 mpu_io=0x330 143 144 145 146 Alma Chao <elysian@ethereal.torsion.org> suggests the following in 147 a /etc/modprobe.d/*conf file: 148 149 alias sound ad1848 150 alias synth0 opl3 151 options ad1848 io=0x530 irq=7 dma=0 soundpro=1 152 options opl3 io=0x388