1. Description

• Normal sequencer and MIDI events:
They are converted to the ALSA sequencer events, and sent to the corresponding port.
• Timer events:
The timer is not selectable by ioctl. The control rate is fixed to 100 regardless of HZ. That is, even on Alpha system, a tick is always 1/100 second. The base rate and tempo can be changed in /dev/music.
• Patch loading:
It purely depends on the synth drivers whether it's supported since the patch loading is realized by callback to the synth driver.
• I/O controls:
Most of controls are accepted. Some controls are dependent on the synth driver, as well as even on original OSS.

• Better queue mechanism:
The events are queued before processing them.
• Multiple applications:
You can run two or more applications simultaneously (even for OSS sequencer)! However, each MIDI device is exclusive - that is, if a MIDI device is opened once by some application, other applications can't use it. No such a restriction in synth devices.
• Real-time event processing:
The events can be processed in real time without using out of bound ioctl. To switch to real-time mode, send ABSTIME 0 event. The followed events will be processed in real-time without queued. To switch off the real-time mode, send RELTIME 0 event.
• /proc interface:
The status of applications and devices can be shown via /proc/asound/seq/oss at any time. In the later version, configuration will be changed via /proc interface, too.

2. Installation

        OSS sequencer emulation version 0.1.8
        ALSA client number 63
        ALSA receiver port 0

        Number of applications: 0

        Number of synth devices: 1

        synth 0: [EMU8000]
          type 0x1 : subtype 0x20 : voices 32
          capabilties : ioctl enabled / load_patch enabled

        Number of MIDI devices: 3

        midi 0: [Emu8000 Port-0] ALSA port 65:0
          capability write / opened none

        midi 1: [Emu8000 Port-1] ALSA port 65:1
          capability write / opened none

        midi 2: [0: MPU-401 (UART)] ALSA port 64:0
          capability read/write / opened none

3. Using Synthesizer Devices

4. Using MIDI Devices

5. Module Options

• maxqlen
specifies the maximum read/write queue length. This queue is private for OSS sequencer, so that it is independent from the queue length of ALSA sequencer. Default value is 1024.
• seq_oss_debug
specifies the debug level and accepts zero (= no debug message) or positive integer. Default value is 0.

6. Queue Mechanism

7. Interface to Synthesizer Device

7.1. Registration

int snd_seq_oss_synth_register(char *name, int type, int subtype, int nvoices,
                              snd_seq_oss_callback_t *oper, void *private_data)

int snd_seq_oss_synth_unregister(int index),

7.2. Callbacks

snd_seq_oss_callback_t:
        int (*open)(snd_seq_oss_arg_t *p, void *closure);
        int (*close)(snd_seq_oss_arg_t *p);
        int (*ioctl)(snd_seq_oss_arg_t *p, unsigned int cmd, unsigned long arg);
        int (*load_patch)(snd_seq_oss_arg_t *p, int format, const char *buf, int offs, int count);
        int (*reset)(snd_seq_oss_arg_t *p);
Except for open and close callbacks, they are allowed
to be NULL.
Each callback function takes the argument type snd_seq_oss_arg_t as the
first argument.
struct snd_seq_oss_arg_t {
        int app_index;
        int file_mode;
        int seq_mode;
        snd_seq_addr_t addr;
        void *private_data;
        int event_passing;
};
The first three fields, app_index, file_mode and
seq_mode
are initialized by OSS sequencer. The app_index is the application
index which is unique to each application opening OSS sequencer. The
file_mode
is bit-flags indicating the file operation mode. See
seq_oss.h
for its meaning. The seq_mode is sequencer operation mode. In
the current version, only SND_OSSSEQ_MODE_SYNTH is used.
The next two fields, addr and private_data, must be
filled by the synth driver at open callback. The addr contains
the address of ALSA sequencer port which is assigned to this device. If
the driver allocates memory for private_data, it must be released
in close callback by itself.
The last field, event_passing, indicates how to translate note-on
/ off events. In PROCESS_EVENTS mode, the note 255 is regarded
as velocity change, and key pressure event is passed to the port. In PASS_EVENTS
mode, all note on/off events are passed to the port without modified. PROCESS_KEYPRESS
mode checks the note above 128 and regards it as key pressure event (mainly
for Emu8000 driver).

7.2.1. Open Callback
The open is called at each time this device is opened by an application
using OSS sequencer. This must not be NULL. Typically, the open callback
does the following procedure:


Allocate private data record.


Create an ALSA sequencer port.


Set the new port address on arg->addr.


Set the private data record pointer on arg->private_data.

Note that the type bit-flags in port_info of this synth port must NOT contain
TYPE_MIDI_GENERIC
bit. Instead, TYPE_SPECIFIC should be used. Also, CAP_SUBSCRIPTION
bit should NOT be included, too. This is necessary to tell it from other
normal MIDI devices. If the open procedure succeeded, return zero. Otherwise,
return -errno.

7.2.2 Ioctl Callback
The ioctl callback is called when the sequencer receives device-specific
ioctls. The following two ioctls should be processed by this callback:


IOCTL_SEQ_RESET_SAMPLES

reset all samples on memory -- return 0

IOCTL_SYNTH_MEMAVL

return the available memory size

FM_4OP_ENABLE

can be ignored usually
The other ioctls are processed inside the sequencer without passing to
the lowlevel driver.

7.2.3 Load_Patch Callback
The load_patch callback is used for sample-downloading. This callback
must read the data on user-space and transfer to each device. Return 0
if succeeded, and -errno if failed. The format argument is the patch key
in patch_info record. The buf is user-space pointer where patch_info record
is stored. The offs can be ignored. The count is total data size of this
sample data.

7.2.4 Close Callback
The close callback is called when this device is closed by the
application. If any private data was allocated in open callback, it must
be released in the close callback. The deletion of ALSA port should be
done here, too. This callback must not be NULL.

7.2.5 Reset Callback
The reset callback is called when sequencer device is reset or
closed by applications. The callback should turn off the sounds on the
relevant port immediately, and initialize the status of the port. If this
callback is undefined, OSS seq sends a HEARTBEAT event to the
port.

7.3 Events
Most of the events are processed by sequencer and translated to the adequate
ALSA sequencer events, so that each synth device can receive by input_event
callback of ALSA sequencer port. The following ALSA events should be implemented
by the driver:
 


ALSA event

Original OSS events



NOTEON

SEQ_NOTEON
MIDI_NOTEON



NOTE

SEQ_NOTEOFF
MIDI_NOTEOFF



KEYPRESS

MIDI_KEY_PRESSURE



CHANPRESS

SEQ_AFTERTOUCH
MIDI_CHN_PRESSURE



PGMCHANGE

SEQ_PGMCHANGE
MIDI_PGM_CHANGE



PITCHBEND

SEQ_CONTROLLER(CTRL_PITCH_BENDER)
MIDI_PITCH_BEND



CONTROLLER

MIDI_CTL_CHANGE
SEQ_BALANCE (with CTL_PAN)



CONTROL14

SEQ_CONTROLLER



REGPARAM

SEQ_CONTROLLER(CTRL_PITCH_BENDER_RANGE)



SYSEX

SEQ_SYSEX



The most of these behavior can be realized by MIDI emulation driver
included in the Emu8000 lowlevel driver. In the future release, this module
will be independent.
Some OSS events (SEQ_PRIVATE and SEQ_VOLUME events) are passed as event
type SND_SEQ_OSS_PRIVATE.  The OSS sequencer passes these event 8 byte
packets without any modification. The lowlevel driver should process these
events appropriately.

8. Interface to MIDI Device
Since the OSS emulation probes the creation and deletion of ALSA MIDI sequencer
ports automatically by receiving announcement from ALSA sequencer, the
MIDI devices don't need to be registered explicitly like synth devices.
However, the MIDI port_info registered to ALSA sequencer must include a group
name SND_SEQ_GROUP_DEVICE and a capability-bit CAP_READ or
CAP_WRITE. Also, subscription capabilities, CAP_SUBS_READ or CAP_SUBS_WRITE,
must be defined, too. If these conditions are not satisfied, the port is not
registered as OSS sequencer MIDI device.
The events via MIDI devices are parsed in OSS sequencer and converted
to the corresponding ALSA sequencer events. The input from MIDI sequencer
is also converted to MIDI byte events by OSS sequencer. This works just
a reverse way of seq_midi module.

9. Known Problems / TODO's



Patch loading via ALSA instrument layer is not implemented yet.

• Information is copyright its respective author.
• All material is available from the Linux Kernel Source distributed under a GPL License.
• Hosted by mjmwired.net.