Documentation / driver-api / dmaengine / pxa_dma.rst


Based on kernel version 6.11. Page generated on 2024-09-24 08:21 EST.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190
==============================
PXA/MMP - DMA Slave controller
==============================

Constraints
===========

a) Transfers hot queuing
A driver submitting a transfer and issuing it should be granted the transfer
is queued even on a running DMA channel.
This implies that the queuing doesn't wait for the previous transfer end,
and that the descriptor chaining is not only done in the irq/tasklet code
triggered by the end of the transfer.
A transfer which is submitted and issued on a phy doesn't wait for a phy to
stop and restart, but is submitted on a "running channel". The other
drivers, especially mmp_pdma waited for the phy to stop before relaunching
a new transfer.

b) All transfers having asked for confirmation should be signaled
Any issued transfer with DMA_PREP_INTERRUPT should trigger a callback call.
This implies that even if an irq/tasklet is triggered by end of tx1, but
at the time of irq/dma tx2 is already finished, tx1->complete() and
tx2->complete() should be called.

c) Channel running state
A driver should be able to query if a channel is running or not. For the
multimedia case, such as video capture, if a transfer is submitted and then
a check of the DMA channel reports a "stopped channel", the transfer should
not be issued until the next "start of frame interrupt", hence the need to
know if a channel is in running or stopped state.

d) Bandwidth guarantee
The PXA architecture has 4 levels of DMAs priorities : high, normal, low.
The high priorities get twice as much bandwidth as the normal, which get twice
as much as the low priorities.
A driver should be able to request a priority, especially the real-time
ones such as pxa_camera with (big) throughputs.

Design
======
a) Virtual channels
Same concept as in sa11x0 driver, ie. a driver was assigned a "virtual
channel" linked to the requestor line, and the physical DMA channel is
assigned on the fly when the transfer is issued.

b) Transfer anatomy for a scatter-gather transfer

::

   +------------+-----+---------------+----------------+-----------------+
   | desc-sg[0] | ... | desc-sg[last] | status updater | finisher/linker |
   +------------+-----+---------------+----------------+-----------------+

This structure is pointed by dma->sg_cpu.
The descriptors are used as follows :

    - desc-sg[i]: i-th descriptor, transferring the i-th sg
      element to the video buffer scatter gather

    - status updater
      Transfers a single u32 to a well known dma coherent memory to leave
      a trace that this transfer is done. The "well known" is unique per
      physical channel, meaning that a read of this value will tell which
      is the last finished transfer at that point in time.

    - finisher: has ddadr=DADDR_STOP, dcmd=ENDIRQEN

    - linker: has ddadr= desc-sg[0] of next transfer, dcmd=0

c) Transfers hot-chaining
Suppose the running chain is:

::

   Buffer 1              Buffer 2
   +---------+----+---+  +----+----+----+---+
   | d0 | .. | dN | l |  | d0 | .. | dN | f |
   +---------+----+-|-+  ^----+----+----+---+
                    |    |
                    +----+

After a call to dmaengine_submit(b3), the chain will look like:

::

   Buffer 1              Buffer 2              Buffer 3
   +---------+----+---+  +----+----+----+---+  +----+----+----+---+
   | d0 | .. | dN | l |  | d0 | .. | dN | l |  | d0 | .. | dN | f |
   +---------+----+-|-+  ^----+----+----+-|-+  ^----+----+----+---+
                    |    |                |    |
                    +----+                +----+
                                         new_link

If while new_link was created the DMA channel stopped, it is _not_
restarted. Hot-chaining doesn't break the assumption that
dma_async_issue_pending() is to be used to ensure the transfer is actually started.

One exception to this rule :

- if Buffer1 and Buffer2 had all their addresses 8 bytes aligned

- and if Buffer3 has at least one address not 4 bytes aligned

- then hot-chaining cannot happen, as the channel must be stopped, the
  "align bit" must be set, and the channel restarted As a consequence,
  such a transfer tx_submit() will be queued on the submitted queue, and
  this specific case if the DMA is already running in aligned mode.

d) Transfers completion updater
Each time a transfer is completed on a channel, an interrupt might be
generated or not, up to the client's request. But in each case, the last
descriptor of a transfer, the "status updater", will write the latest
transfer being completed into the physical channel's completion mark.

This will speed up residue calculation, for large transfers such as video
buffers which hold around 6k descriptors or more. This also allows without
any lock to find out what is the latest completed transfer in a running
DMA chain.

e) Transfers completion, irq and tasklet
When a transfer flagged as "DMA_PREP_INTERRUPT" is finished, the dma irq
is raised. Upon this interrupt, a tasklet is scheduled for the physical
channel.

The tasklet is responsible for :

- reading the physical channel last updater mark

- calling all the transfer callbacks of finished transfers, based on
  that mark, and each transfer flags.

If a transfer is completed while this handling is done, a dma irq will
be raised, and the tasklet will be scheduled once again, having a new
updater mark.

f) Residue
Residue granularity will be descriptor based. The issued but not completed
transfers will be scanned for all of their descriptors against the
currently running descriptor.

g) Most complicated case of driver's tx queues
The most tricky situation is when :

 - there are not "acked" transfers (tx0)

 - a driver submitted an aligned tx1, not chained

 - a driver submitted an aligned tx2 => tx2 is cold chained to tx1

 - a driver issued tx1+tx2 => channel is running in aligned mode

 - a driver submitted an aligned tx3 => tx3 is hot-chained

 - a driver submitted an unaligned tx4 => tx4 is put in submitted queue,
   not chained

 - a driver issued tx4 => tx4 is put in issued queue, not chained

 - a driver submitted an aligned tx5 => tx5 is put in submitted queue, not
   chained

 - a driver submitted an aligned tx6 => tx6 is put in submitted queue,
   cold chained to tx5

 This translates into (after tx4 is issued) :

 - issued queue

 ::

      +-----+ +-----+ +-----+ +-----+
      | tx1 | | tx2 | | tx3 | | tx4 |
      +---|-+ ^---|-+ ^-----+ +-----+
          |   |   |   |
          +---+   +---+
        - submitted queue
      +-----+ +-----+
      | tx5 | | tx6 |
      +---|-+ ^-----+
          |   |
          +---+

- completed queue : empty

- allocated queue : tx0

It should be noted that after tx3 is completed, the channel is stopped, and
restarted in "unaligned mode" to handle tx4.

Author: Robert Jarzmik <robert.jarzmik@free.fr>